High-voltage and low-voltage electronic leak detection (ELD) both find holes in a roof or waterproofing membrane, but they work under opposite conditions. High voltage needs a bone-dry membrane and pinpoints the breach. Low voltage needs a wet surface and narrows the breach to a small area. The deck, the weather, and how the system was installed decide which one fits, and on a wood deck, neither works unless a conductive layer was planned in.
Right now we are testing a white single-ply roof on six buildings in Ocala, Florida. Every morning, the same thing happens. Dew settles on the membrane, and the test waits.
It does not matter whether the humidity was low overnight or the wind blew all night. On that job, high-voltage testing cannot start until about 1 p.m. The membrane has to be totally dry, and until it is, the equipment cannot tell a hole from a wet spot.
That is the practical side of the high-voltage vs. low-voltage ELD question. Both methods find breaches you cannot see. But each one has conditions it needs, and picking the wrong method for the roof, the deck, or the weather wastes a test day or misses a defect.
Both Methods Need a Conductive Path
Every form of ELD works on the same principle. A roofing or waterproofing membrane is an electrical insulator. If the membrane is intact, current cannot pass through it. If there is a hole, a bad seam, or a puncture from another trade, current finds that opening and the equipment detects it.
For that to work, there has to be something conductive under the membrane to complete the circuit. A concrete deck or a metal deck does the job. ASTM D7877, the standard guide for electronic leak detection, describes this requirement and notes that a conductive material can be placed directly under the membrane when insulation or a protection board would otherwise break the electrical path.
Keep that requirement in mind. It is the reason ELD works so well on some buildings and cannot be used at all on others.
How High-Voltage ELD Works
High-voltage testing uses a tool we call the broom: a wand with a brush of conductive bristles that the technician sweeps across the membrane. When the broom passes over a breach, the current jumps to the deck below. The equipment beeps and you can see the spark right at the hole.
Mark's way of describing it: high voltage says, "There it is." No searching, no narrowing down. The defect is marked where the spark lands.
That precision comes with one hard requirement. The membrane has to be completely dry. Water conducts electricity, so any moisture on the surface reads as a false positive. Dew, a light rain, or water trapped under a seam all stop the test or make the results unreliable.
We use high voltage most often on single-ply roofs, where the membrane is exposed, the surface drains, and we can wait for the sun to do its work. On the Ocala job, that means scheduling around the dew, not the calendar.
How Low-Voltage ELD Works
Low-voltage testing works the other way around. Instead of a dry surface, it needs a wet one.
The technician lays a perimeter wire around the test area and wets the membrane surface. Then they use two probes, which Mark compares to ski poles, to read how the current moves across the surface. Current pulls toward a breach, and the technician follows it in until the reading narrows to a small area, typically about 2 feet by 2 feet.
In Mark's words, low voltage says, "It's in here somewhere." It is slower than high voltage and less precise, but it gets you to a small enough area to find and fix the breach.
Low voltage earns its place in a few specific situations:
- Flat plaza decks. Plaza decks are usually dead flat, so they hold water after a rain. High voltage cannot read through standing water. Low voltage uses that water.
- Protection mats set on ribbons of hot rubber. Some waterproofing installers set the protection mat on ribbons of hot rubber instead of a full bed. Rain or heavy dew can then get under the mat, which rules out high voltage entirely. With a full bed of hot rubber, water cannot get underneath.
- Schedule. On a flat plaza deck, low voltage lets us test on schedule without waiting for the surface to dry.
High Voltage vs. Low Voltage at a Glance
| High-voltage ELD | Low-voltage ELD |
|---|---|
| Tool | Broom swept across the membrane |
| Surface condition | Totally dry |
| How it finds a breach | Beep and spark right at the hole |
| Precision | Pinpoints the defect |
| Where we use it most | Exposed single-ply roofs |
| Main limitation | Moisture causes false positives |
How We Choose Between Them
We do not pick a method out of habit. Before a test, we work through a few questions:
- What is the deck? Concrete or metal can complete the circuit. Wood cannot (more on that below).
- Can the membrane be dry when we test? If yes, high voltage gives the most precise results. If the surface holds water or the area stays damp, low voltage is the better fit.
- Is the surface flat? A dead-flat plaza deck that holds water after every rain points toward low voltage.
- How was the protection layer installed? A protection mat on ribbons of hot rubber can trap water underneath, which rules out high voltage.
- What does the specification require? Many waterproofing specifications call for testing before overburden and may name a method or a standard. That requirement comes first.
On a large project, the answer can be both. An exposed roof on the same building as a plaza deck may get high voltage on the roof and low voltage on the deck.
Timing matters as much as method. On any assembly that will be covered with insulation, drainage mat, pavers, or a green roof, the test has to happen before that material goes down. We explain why in our post on why you should test before the overburden goes on.
Where ELD Cannot Be Used
ELD is a strong tool, but it has limits. Knowing them early saves a wasted mobilization and a surprised project team.
Wood decks
Wood is not conductive. Without a conductive deck, there is no circuit, and neither method works.
We ran into this on a three-story residential building near Charlotte with a low-slope roof. ELD looked like the obvious test. But the roof deck was wood, so ELD was not an option.
Most wood-framed multifamily
The same limit applies to most apartment and other wood-framed multifamily buildings. The roof can be made testable by planning a conductive layer, such as a conductive primer or conductive insulation facer, into the assembly from the start. That adds cost, and in our experience most multifamily projects do not include it.
That is a tradeoff the owner and design team should make on purpose. If the conductive layer is left out, ELD is off the table for the life of that roof.
Steep-slope roofs
ELD is not used on shingles, metal panels, or clay tile. Leak tracing on steep-slope roofs relies on water testing instead.
What This Means for Your Project
- General contractors: Build the test into the schedule with weather in mind. A high-voltage test day can start late if the membrane is wet in the morning, and that is no one's fault.
- Architects and spec writers: If the owner wants the option of ELD on a wood-framed building, a conductive layer has to be in the design. It cannot be added after the membrane is down.
- Owners: Ask whether your roof or plaza deck can be tested electronically before you need it. The answer depends on the deck, and it is better to know before a leak than after.
For a broader look at what the testing finds, see our post on electronic leak detection testing.
Talk with us about testing on your project. We will tell you which method fits your roof or deck, and whether ELD is an option at all.
Related Articles
- Electronic Leak Detection Testing: What ELD Finds That Visual Inspections Miss
- Why Waterproofing Leak Detection Has to Happen Before the Overburden
